Moxa Technologies EtherDevice Installationsanleitung

Moxa EtherDevice™ Switch EDS-600 Series Hardware Installation Guide First Edition, August 2009 © 2009 Moxa Inc. All rights

- 10 -NOTE Before tightening the screws into the wall, make sure the screw head and shank size are suitable by inserting the screw through one of the

- 11 -Please read and follow these guidelines: y Use separate paths to route wiring for power and devices. If power wiring and device wiring paths m

- 12 -Wiring the Relay Contact The EDS-600 has a set of relay outputs. The relay contact uses two of the terminal block’s contacts located on the EDS

- 13 -Wiring the Digital Inputs The EDS-600 has one set of digital inputs (DIs). Each DI consists of two contacts of the 5-pin terminal block connect

- 14 -RJ45 (10-pin) to DB9 (F) Cable Wiring RJ45 Plug Pin 1MoxaEtherDeviceServerRJ45ConnectorDCDDSRRTSGNDTxDRxDCTSDTRCOM PortFemale DB9ConnectorDCDDT

- 15 -RJ45 (8-pin) to RJ45 (8-pin) Straight-through Cable Wiring Straight-Through CableRJ45 Plug Pin 1Switch PortRJ45ConnectorRJ45ConnectorTx+Tx-Rx+R

- 16 - ATTENTION This is a Class 1 Laser/LED product. To avoid causing serious damage to your eyes, do not stare directly into the laser beam. Turbo

- 17 -“Turbo Ring V2” DIP Switch Settings DIP 1 DIP 2 DIP 3 DIP 4 ON: Enables the default “Ring Coupling (backup)” port. ON: Enables this EDS as

- 18 -BlinkingWhen the EDS-600 is set as the Ring Master of the Turbo Ring or as the Head of the Turbo Chain and the Turbo Ring or Turbo Chain is dow

- 19 -Interface RJ45 Ports 10/100/1000BaseT(X) auto negotiation speed, F/H duplex mode, and auto MDI/MDI-X connection Fiber Ports Optional 100/100

- 2 -Package Checklist The Moxa EDS-600 series is shipped with the following items. If any of these items is missing or damaged, please contact your

- 20 -Hazardous Location UL/cUL Class I, Division 2, Groups A, B, C, and D; ATEX Zone 2, Ex nC nL IIC T4 (Pending) EMI FCC Part 15, EN61000-6-4 EMS

- 3 -Panel Views of the EDS-608 127465103988FRONT VIEWREAR VIEW Front Panel: 1. System Status LEDs 2. Fast Ethernet Interface Module port LEDs 3.

- 4 -Panel Views of the EDS-611 1102746512311989FRONT VIEWREAR VIEW Front Panel: 1. System Status LEDs 2. Fast Ethernet Interface Module port LEDs

- 5 -Panel Views of the EDS-616 127465103988FRONT VIEWREAR VIEW Front Panel: 1. System Status LEDs 2. Fast Ethernet Interface Module port LEDs 3.

- 6 -Panel Views of the EDS-619 1274651210311998FRONT VIEWREAR VIEW Front Panel: 1. System Status LEDs 2. Fast Ethernet Interface Module port LEDs

- 7 -Mounting Dimensions (unit = mm) EDS-608/EDS-611 Front View Side ViewRear ViewRear View DIN-Rail Attachment PlatePanel Mounting KitPanel Mounting

- 8 -EDS-616/EDS-619 Front View Side ViewRear ViewRear ViewDIN-Rail Attachment Plate DIN-Rail Attachment PlatePanel Mounting KitPanel Mounting Kit DI

- 9 -STEP 2—Insert the top of the DIN-Rail into the top slots on the DIN-Rail attachment plate. STEP 3—The DIN-Rail attachment unit will snap into pl